All NATO watch straps have in common that they are relatively long, so they can also be worn on very large wrists or even over clothes. In most cases, however, there is always a fair amount of strap left and sticks out from the wrist, so it must be threaded back into the metal loops. Sometimes it is either too much or too less strap left over to be thread back into the loops, and this is the most annoying case. If you have a very small wrist and the NATO strap length needed to be greatly reduced, it is necessary to punch new holes in the bracelet too.
In the following video and blog post we show you 3 simple tricks how to shorten your NATO strap, how you punch new holes in it and how you customize your regular double pass- to a single pass NATO within just a few minutes.
- Piercing tool
- Rivet pliers / -punch
- Two coins
Trick Nr. 1: How do I shorten a NATO watch strap?
1. Determine the new length of your NATO strap
Use two coins with the same rounding scope like the end of the NATO strap and holt it between them to determine the position where you want to shorten the NATO. You can also use the shape of the coins for drawing a line to mark where you want to cut it off.
2. Cut off the end of the strap
Now simply cut along the shape of the coins (or along the marking) to give the shortened bracelet a rounded end again. You can use a common scissor to cut off the end of the NATO strap.
3. Place the cut end between two coins
Use a tool, for example a pincer, and firmly hold the cut end of the NATO strap between two coins. Make sure the cut end of your NATO and the two coins line up. This will protect the fabric from scorching or melting too far in the next step and you will have a clean welded end.
4. Weld the cut end of your shortened NATO
Now use a lighter and move back and forth relatively quickly at the end and thus weld the protruding nylon fibers. This will prevent the nylon fibers on the cut end from loosening.
Trick Nr. 2: How to punch an extra hole in your NATO strap ?
1. Punch new holes into the NATO strap
When the strap has become shorter, you probably need new holes to fit the strap on your wrist again. Best tool for new holes in you watch strap is a Rivet pliers or -puncher. Choose the right size, so that the pin of your buckle fits through it and punch a new hole. You can punch it in the same distance as the other holes, or you mark an individual hole, whatever is best for the perfect fit on your wrist.
2. Weld the new holes with a lighter
Now use a lighter and heat up the piercing tool at the end and thus weld the protruding nylon fibers around the holes. This will prevent the nylon fibers on the holes end from loosening.
Trick Nr. 3: How to go from a double pass nato to a single pass nato ?
A regular NATO strap is a two-layer strap and the watch sits safe “between” the two layers. If the very rare case of spring bar failure occurs, the watch will still hang on its last spring bar between the strap and it won’t fall off your wrist. But it also adds additional height to your watch, which some people don’t like and also makes heavy watches “wobble” on top of your wrist. If you can’t find a single-pass NATO strap that you like, you can simply customize your classic NATO strap into a single-pass NATO strap. – If you want to learn more about NATO straps, check out our blog post “All you need to know about NATO straps” here.
1. Cut the second layer of your NATO strap
Cut the short second layer of the NATO strap close to the stitching, but not too close, just so you have a couple of mm’s left.
2. Weld the end with a lighter
Use a lighter and quickly go back and forth over the cut part, so all the cut open nylon fibers melt and seal. This will stop the fabric from raffling and make them feel smooth on the wrist.
Thanks to our brand ambassador @BowlOfSalmon for providing film and picture material – Check out his blog on bowlofsalmon.com
Do-It-Yourself (DIY) projects are purely “at your own risk”. As with any DIY project, unfamiliarity with the tools and process can be dangerous. Posts should be construed as theoretical advice only. If you are at all uncomfortable or inexperienced working on these projects, please reconsider doing the job yourself. It is very possible on any DIY project to damage your cottage, void your property insurance, create a hazardous condition, or harm or even kill yourself or others. This website will not be held responsible for any injury due to the misuse or misunderstanding of any DIY project.
By using this website, you agree to indemnify Horology Ventures UG (haftungsbeschränkt) (“The Company”), its officers, directors, employees, agents, distributors, affiliates, subsidiaries and their related companies for any and all claims, damages, losses and causes of action arising out of your breach or alleged breach of this agreement.
The materials provided in this DIY post are for educational and promotional purposes only. You may not rely on any information and opinions expressed in it for any other purpose. Neither the Company, nor its officers, directors, employees, agents, distributors, affiliates, subsidiaries and their related companies are responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted on the Company’s website.